Open Gun - 40 Pro Ported SKU10100 - MP-Pistol Forum

Open Gun - 40 Pro Ported SKU10100

This is a discussion on Open Gun - 40 Pro Ported SKU10100 within the Competition forums, part of the Shooting category; Looking at building an Open gun in the spring using the M&P 40 Pro Ported. I have not shot the ported gun and am wondering ...


Go Back   MP-Pistol Forum > Shooting > Competition

Reply
 
LinkBack Thread Tools Display Modes
Old November 27th, 2014, 07:07 AM   #1
Member
 
Join Date: Jun 2012
Location: Terrace, BC
Posts: 182
Open Gun - 40 Pro Ported SKU10100

Looking at building an Open gun in the spring using the M&P 40 Pro Ported. I have not shot the ported gun and am wondering if it provides enough downward pressure on firing to offset the recoil and act like a compensater on an Open
gun.

I am thinking 40 cal would be easier to make major.

I should add we are limited to 10 rounds in CANADA when we play IPSC so the capacity issue is a wash between the 40cal and the 9MM.

Has anyone tried this?

Take Care

Bob

Last edited by Canuck44; November 27th, 2014 at 07:29 AM.
Canuck44 is offline  
Old December 4th, 2014, 03:26 PM   #2
Member
 
GuyMoto's Avatar
 
Join Date: Feb 2014
Location: Sauk Rapids, MN
Posts: 54
Just started to make my first USPSA Limited/Open gun. I am starting out with the Pro CORE in 40. In the 5 inch variety. JUst installed a Apex Flat trigger kit and will be changing out some of the springs to lighten the trigger pull. Have the RAM on order.. Just ordered magwell and base plates to fit the magwell. I have a Burris Fastfire Red Dot currently on board but will probably remove it and run iron sights first. Thinking of a barrel upgrade also.
GuyMoto is offline  
Old June 24th, 2015, 05:08 AM   #3
Junior Member
 
Dead2Rights's Avatar
 
Join Date: Dec 2011
Location: Fort Lauderdale, FL
Posts: 12
I am using the CORE Ported 9L. The current "barrel porting" is venting off about 12-15% of your muzzle blast to push your muzzle down. (For every action there is an equal and opposite re-action) When using porting the recoil is slightly reduced and your control of the muzzle is more manageable.

When using a compensator, the principles are more exaggerated. The gases out of the muzzle, which is peaking into the first expansion chamber, will be diverted upward, bleeding off 30% of the recoil whereas the next port will bleed off another 5%, then the third with 5% and the forth if used, will be about 5%. More than 4 ports on a compensator do not make any significant differences. Bottomline, a compensator will reduce your recoil by 40-45%. Much more dramatic. This also however changes the dynamics and new recoil springs and hotter loads may need to be looked at to drive the slide weight properly if so much of the gas used to cycle the weapon is being blown off.

Check out my video series I just started on my S&W M&P Open Gun http://www.youtube.com/watch?v=n7t39JK2yPk

Sent from my SAMSUNG-SM-N915A using Tapatalk
Dead2Rights is offline  
Reply

  MP-Pistol Forum > Shooting > Competition


Search tags for this page

10100 smith & wesson

,

smith and wesson 10100 .40l

Click on a term to search for related topics.

Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
New M&P Performance Ported...what to do with it? cobrar97 MP Full Size Pistols 4 November 20th, 2014 01:34 PM
open season on open carry.... 3djedi MP Talk 0 August 9th, 2013 03:05 PM
Ported Barrel? shawnyboy MP Compact Pistols 15 December 14th, 2011 07:32 PM
Ported 9mm... burnsome MP Full Size Pistols 18 October 30th, 2007 06:38 PM



Powered by vBulletin 3.8.7
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
SEO by vBSEO 3.6.1
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright © 2006-2012 MP-Pistol. All rights reserved.
MP-Pistol is a M&P pistol enthusiast forum, but it is in no way affiliated with, nor does it represent Smith & Wesson Holding Corp. of Springfield, MA.